NXP i.MX RT 1052 based
Single Board Computer OK1052-C
OK1052-C is a single board computer/ development board designed based on NXP Cortex -M7 crossover processor i.MX RT1052 belongs to i.MX RT1050 series MCU. It operates at speeds up to 528MHz to provide high CPU performance and best real-time response. The i.MX RT1052 processor has 512 KB on-chip RAM,which can be flexibly configured as TCM or general-purpose on-chip RAM. 16MB/ 32MB SDRAM, 4MB/ 16MB QSPI-NorFlash are optional.
The OK1052-C consists of SoM and carrier board and is an industrial grade item with working temperature ranges from -40℃ to +85℃. Peripheral pins such as UART， Ethernet， USB， CAN， PWM， ADC， LCD and CAMERA are all available on carrier board. What's more, OS uClinux is supported very well.
▊ Hardware Features
| Overview of FET1052-C System on Module | |||
|---|---|---|---|
| CPU | i.MXRT1052 | Power In | 5V |
| Architecture | Cortex-M7 | Dimensions | 31mm×43mm |
| Frequency | 528MHz | PCB | thickness 1.6mm, 4-layer PCB, ENIG |
| RAM | SRAM 512KB; SDRAM 16MB/32MB | Package | board to board connector, 2*80pin, pitch 0.8mm |
| Flash | QSPI Nor Flash 4MB/16MB | Working Temperature | -40℃~+85℃ |
| OS | Bare metal, FreeRTOS, uCLinux, RT-Thread | ||
| FET1052-C System on Module Features | ||
|---|---|---|
| Interface | QTY | Spec. |
| LCD | 1 |
upto RGB888, resolution up to 1366* 768*(WXGA), 480*x 272 and 800* 480 are available |
| CAMERA | 1 |
8-bit DVP, up to 5.0MP |
| SD/MMC/SDIO | ≤2 |
SD card or SDIO card with 1-bit or 4-bit mode |
| USB | 2 |
1x USB2.0 OTG(up to 480Mbps), 1x USB2.0 host, integrated with HS USB Phy |
| SAI | ≤3 |
up to 3x IIS audio |
| SPDIF | 1 |
Sony/ Philips digital audio interface |
| UART | ≤8 |
each up to 5.0Mbps |
| SPI | ≤4 |
full duplex enhanced sync. serial interface, up to 52Mbit/s, it could be configured to host/ device mode, four chip selections are available IIC≤4 |
| IIC | ≤4 | |
| Ethernet | ≤1 | 10/100Mbps auto-negotiation |
| PWM | ≤32 | 32x PWM |
| SWD | supported | |
| KeyPad | supported | 8*8 |
| QSPI | 2 | |
| CAN | ≤2 | CAN 2.0B |
| ADC | ≤20 |
2x 12-bit ADC, up to 20 input channels |
| SEMC BUS | 1 |
16-bit parallel bus |
| OK1052-C Carrier Board Features | ||
|---|---|---|
| Interface | QTY | Spec. |
| LCD | 1 |
up to RGB888, resolution up to 1366* 768*(WXGA), 480*x 272 and 800* 480 are available |
| CAMERA | 1 |
8-bit DVP, up to 5.0Mp |
| Audio | 1 | 1*MIC, 1*Phone |
| USB Host | 1 |
USB2.0(up to 480Mbps) |
| USB OTG | 1 |
standard micro USB connector, USB2.0 OTG(up to 480Mbps) |
| Ethernet | 1 |
10M/ 100Mbps auto-negotiation, RJ-45 |
| RTC | 1 | RX8010SJ, CR1220 |
| EEPROM | 1 |
24C02 chip with capability of 256 bytes |
| TF Card | 1 |
compatible of MICRO SD, SDHC |
| LED | 1 |
users indicator |
| POR_BUTTON | 1 |
reset key |
| WAKEUP | 1 | |
| ON/OFF | 1 |
keep pressing it to power on or power off the board |
| BOOT | 1 |
DIP switch for booting mode selection, presently, only TF card mode and QSPI NOR Flash mode are supported |
| PWM | 1 |
for LCD backlight adjusting |
| ADC | 5 |
4x ADC for resistive touching panel, and 1x ADC for adjustable resistor |
| IIC | 1 |
for mounting of touching, camera, WM8960, EEPROM, RTC, IIC converted to 4-wired touching chip |
| CAN | 1 | CAN 2.0B |
| SPI | 1 |
pin connectors (10-pin) with pitch of 2.0mm |
| UART | 1 |
3 wired UART, 3.3V, up to 5.0Mbps, 10-pin header with pitch of 2.54mm |
| IIS | 1 | WM8960 |
| UART Debug | 1 |
RS232, DB9 connector |
| SWD | 1 |
debug port, 8-pin hearder with pitch of 2.54mm |
| Resistive Touch | 1 |
the carrier board compative the original touch and TSC2007 touching chip, TSC2007 is the default configuration |
| KEY BOARD | 1 |
4* 4 metrix keypad port by 8-pin header with pitch of 2.54mm |
▊ Software Features
| Bare Metal DEMO | ||
|---|---|---|
| gpt | lpi2c | |
| pit | kpp | |
| PWM | enc | |
| BEE | ||
| rtwdog | sai | |
| ewm | lpspi | |
| dcp | enet | |
| snvs | flexspi | |
| src | sdcard | |
| trng | sdcard_fatfs | |
| cache | edma | |
| flexcan | tsc | |
| gpio | usb(HOST, OTG) | |
| gpio | semc | |
| adc | csi:CMOS | |
| adc_etc | elcdif | |
| cmp | PXP | |
| qtmr | emwin | |
| lpuart（UART2） | flexram | |
| uCLinux Demo | ||
| build up of compiling environment | Ethernet | |
| Compile application | UART | |
| Make file system image | LED GPIO OUT | |
| TF card booting/ iamge flashing | User key | |
| micro SD/TF card driver | LCD FrameBuffer | |
| USB HOST | Tsc resistive touching | |
| USB OTG | RTC | |
| I2C EEPROM | ||
| FreeRTOS Demo | ||
| lpi2c | Lwip | |
| event | queue | |
| mutex | sem, sem_static | |
| swtimer | tickless | |
| generic | ||
| RT-Thread Demo | ||
| read and write file system | UART testing | |
| gpio | enet | |
| i2c | rtc | |
| spi | LCD/resistive touch screen/emwin testing | |
▊
How to buy
Payment term: 100% payment in advance no matter sample orders or bulk purchasing orders.
1. Order Online
We have an online store on Alibaba, please contact us to start ordering
2. Western Union
Tell us which item and model you want to order, and we will send you a PI with Western Union account.
3. Bank Transfer(T/ T)
Tell us model and quantity, and we'll send you a PI with our company's bank account for payment.
▊ Shipment
Payment term: 100% in advance
1. Delivery: Goods will be sent out by express as requested
2. Lead time: generally, goods could be sent out within five working days for a sample order, for a bulk requirement order, please contact us to check stock status and estimated delivery time.
3. Shipping charge: buyers should bear related shipping cost.
▊ Recommended system on module(SoM)
