OK335xS Single Board Computer

CPU: AM3354

Architecture: Cortex-A8

Frequency: 800MHz

RAM: 512MB DDR3

ROM: 256MB NandFlash,1GB NandFlash

System: Linux3.2+QT4.8,Android2.3,Android4.2,LinuxRT,WinCE6.0,Win CE7.0

OK335xS Single Board Computer

OK335xS single board computer integrates with TI AM335x processor and is the most simple and stable industrial development platform. Its main frequency reaches up to 800MHz, operating temp ranges from -40℃ to +85℃.And it support many industrial bus, such as: CAN, PROFIBUS, RS485, etc, support two gigabyte Ethernet port, 324-pin CPU module, each pin is multiplexed with up to 8 configured functions.FE T3 35xS CPU modules have 512M DDR3 RAM and 256M Nandflash on it, could greatly help users to reduce the cost of product development.


OK335xS base board is specially designed for the industrial application, so RS485, CAN, and RS282 interfaces are available on the board for selection. Users could fully use PIN MUX to define functions on the base board. All boards must pass strict EMC/EMI test before leaving factory, could be directly applied into product manufacture.













Hardware Features
FET335xS System on Module Features
CPU TI AM3354 Cortex-A8 I2C 3x IIC
Architecture ARMv7 Cortex-A8 SPI 2x SPI
Frequency 800MHz CAN 2x CAN
RAM 512MDDR3 USB OTG 1x USBOTG2.0
Flash 256M SLC NandFlash USB DEVICE 1x USB DEVICE 2.0
Working Temperature -40℃~+85℃ SD/MMC/SDIO 3x MMC
Relative Humidity 10%~90%(non-condensing) Ethernet 2x Gigabit Ethernet
Voltage Input 5V UART/IrDA 6x  UART/IrDA
2D/3D supported EINT/GPIO more than 20
GPU PowerVR SGX530 ADC 8x ADC
PMU TPS65217C VideoEncoder software codec
Dimensions 52mm*42mm JTAG 1x JTAG
Package edge soldering EEPROM supported, for encrytion
OS Android2.3/4.2, Linux3.2, WinCE7.0, WinCE6.0, StarterWare PWM 3x PWM
LCD RGB24-bit SATA None(can be expanded by USB)
Audio IIS
OK335xS Carrier Board Features
AUDIO 3x audio(1x Phone, 1x MIC, 1x Line in) JTAG 1x JTAG
I2C 1x IIC ADC 5(4 for resistive touching, 1 sliding

rheostat)

SPI 1x SPI Key 5x key
CAN 1x CAN DIP booting mode selection
RS485 1x RS485, multiplexed with Profibus Reset 1x reset
SD/MMC/SDIO 1x SD/ MMC/ SDIO(1x SD card slot) PWM 2x PWM(1x backlight, 1x buzzer)
USB Host 4x USB host, USB2.0 LED 1x LED
USB Device 1x USB Device, USB2.0 GPIO more than 20
Ethernet 2x Gigabit Ethernet RTC supported
UART 4x UART(3x RS232, 1x TTL) SATA can be expanded by USB
Power In 5V GPS serial interface
LCD 1x LCD, can support both resistive and capacitive touching, LCD can be convertedtoVGA or LVDS output 3G USB interface

Software Features

OS Android2.3/4.2
Android Android4.2
Kernel Linux-3.2.0
OS Flashing one-key to flash, or flash a single
Cross-compiler arm-eabi-4.6
Development Environment Ubuntu12.04.2










Driver

NIC touch(resistive/ capacitive)
LED AD
LCD RTC
USB2.0 audio(IIS)
watchdog CAN
PWM(backlight and buzzer) RS485
Flash ECC verification SPI
NandFlash UART(3)
UBI file system EEPROM
SD card Key
LCDFrameBuffer I2C

OS Linux3.2
U-Boot u-boot-2011.09
Kernel Linux-3.2.0, PSP:04.06.00.10, SDK:05.07.00.00
OS Image Flashing flash OS image to NAND Flash by SD card, or flash a single file to NAND Flash
Development Environment Ubuntu12.04.2









Driver

NIC(dual 1000M/100M) RTC
LED audio(IIS)
LCD SPI
USB2.0 UART(3)
PWM(backlight and buzzer) key
Flash ECC verification EEPROM
NandFlash watchdog
UBI file system AD
SD card RS485
LCDFrameBuffer CAN
precise touching(capactive/ resistive) I2C

OS WinCE6.0
BootLoader EBOOT flashed by SD card
OS Image Flashing by SD card
CE Version WinCE6.0
Development Environment VS2005









Driver

LED key
GPIO RTC
I2C EBOOT
SPI NAND Flash
UART GPU
Touch NIC
SD card USB
DMA backlight
audio AD
watchdog PWM

OS Wince7.0
BootLaoder EBOOT can support USB2.0 high speed download mode
OS Image Flashing Flash OS image or a single file to NAND Flash by SD card
CE Version WinCE7.0
Development Envionment VS2005 and VS2008









Driver

LED watchdog
GPIO USB2.0
IIC key
SPI EEPROM
UART PWM(backlight, buzzer)
audio CAN
NandFlash RS485
display AD
touch DMA
SD card



▊ Download


Brochure: Forlinx latest catalog

Hardware Manual: OK335xS/ FET335xS manuals





How to buy


Payment term: 100% payment in advance no matter sample orders or bulk purchasing orders.

1. Order Online

We have an online store on Alibaba, please contact us to start ordering

2. Western Union

Tell us which item and model you want to order, and we will send you a PI with Western Union account.

3. Bank Transfer(T/ T)

Tell us model and quantity, and we'll send you a PI with our company's bank account for payment.


Shipment


Payment term: 100% in advance

1. Delivery: Goods will be sent out by express as requested

2. Lead time: generally, goods could be sent out within five working days for a sample order, for a bulk requirement order, please contact us to check stock status and estimated delivery time.

3. Shipping charge: buyers should bear related shipping cost.


Recommended system on module(SoM)


SoM FET335xS