TI Sitara
AM5718 based
Single Board Computer OK5718-C2
OK5718-C2 is a development board/single board computer designed based on SoM FET5718-C, it consists of carrier board and SoM (system on module) and has below features
★ ARM Cortex -A15, frequency up to 1. 5GHz;
★ DSP C66x with frequency of 750MHz
★ 2x dul-core ARM Cortex -M4 with frequency of 213MHz;
★ 2x dual-core PRU with frequency of 200MHz;
★ High-speed transmission interfaces like USB 3.0, PCIe 3.0, HDMI 1.4, UART*10, QSPI*1, CAN*2, Gagibit Ethernet*2 are available and also
powerful multi-media performance, wide range of applications;
★ OS options: Linux 4.9.41 + QT5.6, TI-RTOS;
★ 12-layer EINT PCB designing;
★ the development board consists of carrier board and SoM, and the carrier board designed with 4-layer PCB and SoM with 12-layer PCB;
★ carrier board dimensions of 130*190mm, and connector hight between SoM and carrier board is just 2mm
★ SoM with 320 pins that all functions of CPU are available;
★ Industrial grade temp width: -40℃ to +85℃
▊ Hardware Features
Overview of FET5718-C System on Module | |||
---|---|---|---|
CPU | TI Sitara AM5718 | ||
Architecture | Cortex-A15-1.5GHz | DSP-C66X-750MHZ | 2xDual Cortex-M4-213MHz |
2xDual-Core PRU-200MHz | PowerVR SGX544 3D GPU | Vivante GC320 2D GPU | |
RAM | 1GB DDR3L | Flash/ Storage | 8GB eMMC |
Dimensions | 50*70mm | Pakcage | board to board connector |
PMU | TPS659162RGZR | Voltage Input | 5V |
Working Temp Width | -40℃~+85℃ | RH | 10-90%RH non-condensing |
OS | Linux4.9.41+ QT5.6+Wayland |
FET5718-C System on Module Features | ||
---|---|---|
Peripheral | QTY | Spec. |
LCD | ≤3 | GB888 24-bit |
HDMI | 1 |
HDMI 1.4a, 1080P@60Hz; 36-bit RGB display; HDCP 1.4 encryption; Deep color mode (10-bit, 12-bit color depth are both supported by pixel clock of 148.5MHz) |
CAMERA | ≤4 |
2x 8-bit DVP, up to 5.0MP
2x 8/ 16/ 24-bit DVP |
MIPI CSI-2 | 2 |
CSI-2_PHY1: 1 clock lane+ 4 data lane CSI2_PHY1: 1 clock lane+ 1 data lane CSI2_PHY1: 1x clock lane+ 4x data lane CSI2_PHY1: 1x clock lane+2x data lane |
SD/MMC/SDIO | ≤4 |
1-bit or 4-bit transferring mode is supported by SD and SDIO card with UHS-I SDR104 mode (up to 104MB/s)
SD/ MMC/ SDIO1: 4-bit data
SD/ MMC/ SDIO2: 8-bit data (used as eMMC on SoM)
SD/ MMC/ SDIO3: 8-bit data
SD/ MMC/ SDIO4: 4-bit data |
IIC | ≤5 |
IIC1/ 2: up to 400Kbps, standard OD IIC3/ 4/ 5: up to 3.4Mbps, analogy OD |
HDQ1W | ≤1 |
Support TI/ Benchmarq HDQ master device function Comply with Dallas 1-Wire protocol |
UART | ≤10 |
can support 5/ 6/ 7/ 8 data bits, parity bit, 1, 1.5, 2 stop bits UART1: full serial interface is supported UART3: IrDA 1.4, CIR are supported others are standard interface |
SPI | ≤4 |
up to 4x SPI, each with up to 4 master channel |
QSPI | ≤1 |
work as master mode only 6 signal pins |
McASP | ≤8 |
supports 8-ch audio at most McASP1/2: up to 16 separate TX/ RX channel McASP3-8: up to 4 separate TX/ RX channel |
USB3.0 | ≤1 |
super speed USB3.0 Dual-Role-Device, Host is supported |
USB2.0 | 1 |
high-speed USB 2.0 Dual-Role-Device, Host is supported |
SATA | 1 | SATA Gen2 |
PCIe | ≤2 |
PCI Express 3.0 subsystem, with 2x 5-Gbps channel 1x Dual-channel interface with GEN2 standard, 2x Single-channel intgerface with Gen2 standard |
CAN | ≤2 |
two CAN controller at most, complys with CAN2.0 protocol |
Ethernet | ≤2 |
3-port gigabit ethernet switch subsystem provides ethernet packet communication and can be configured as an ethernet switch. It provides two network ports and available for RGMII/ RMII/ MII interface, 10M/ 100M/ 1000M adaptive |
PWMSS | ≤3 |
supports up to 3x PWMSS, each is available for: eHRPWM: 16-bit timer, up to 2 separate PWM output eCAP: 32-bit timer, one channel is special for input capture pin eQEP: rotating decode unit |
JTAG | supported | standard IEEE1149.1 |
KeyPad Port | supported | 9*9 keyboard |
GPMC | 1 |
8-bit/ 16-bit data bus width up to 28-bit address bus up to 8-bit chip selection bus |
OK5718-C2 Single Board Features | ||
---|---|---|
Peripheral | QTY | Spec. |
LCD | 3 |
RGB 888, supports reolution up to 1920*1080 (60Hz) |
HDMI | 1 |
HDMI V1.4, up to 1080P 60FPS |
CAMERA | 2 |
MIPI OV5640, MIPI OV5645 |
Audio | 1 | 1*MIC, 1*Phone |
USB Host | 2 |
expended by HUB, USB 2.0 (up to 480Mbps) |
USB3.0 | 1 | up to 5Gbps |
Ethernet | 1 | 10/100/1000Mbps auto-negotiation, RJ45 connector |
WiFi | 1 |
RL-UM02WBS-8723BU-V1.2 IEEE 802.11b/g/n 1T1R WLAN and Bluetooth |
Bluetooth | 1 | |
SD Card | 1 | compatible with SD, SDHC and SDXC(UHS-I) |
SDIO | 1 |
drawn out by 20-pin heards with pitch of 2mm, multiplexed with SD card |
LED | 2 |
for user's definition |
GPMC | 1 | GPMC |
QSPI | 1 | on-board 256Mb QSPI NOR FLASH |
SPI | 1 | |
IIC |
3 |
IIC1: LCD(P8); IIC3: WM8960, LCD(P7), MIPI OV5645 IIC5: LCD(P20), mini PCIe, RTC, MIPI OV5640 |
CAN | 1 | CAN 2.0B |
UART Debug | 1 |
RS232, DB9 connector |
JTAG Debug | 1 | |
RS485 | 1 |
|
RTC | 1 |
RX8010SJ, IIC5 |
▊ How to buy
Payment term: 100% payment in advance no matter sample orders or bulk purchasing orders.
1. Order Online
We have an online store on Alibaba, please contact us to start ordering
2. Western Union
Tell us which item and model you want to order, and we will send you a PI with Western Union account.
3. Bank Transfer(T/ T)
Tell us model and quantity, and we'll send you a PI with our company's bank account for payment.
▊ Shipment
Payment term: 100% in advance
1. Delivery: Goods will be sent out by express as requested
2. Lead time: generally, goods could be sent out within five working days for a sample order, for a bulk requirement order, please contact us to check stock status and estimated delivery time.
3. Shipping charge: buyers should bear related shipping cost.
▊ Recommended System on Module: